Is $343 a fair price to get an electric dryer heating again? Usually, yes, though not always for the reasons on the invoice. Angi puts the national average dryer repair at about $180, with most households paying $100 to $430, so a no-heat job with a new element lands in the upper middle of normal. What matters is how that total was built.
Below, one hypothetical invoice gets read line by line: what each charge should cost in 2027, which ones ought to be credited back, and where a decent technician and a padded bill start to look different. The figures come from published 2026 pricing by Angi, HomeGuide, Fixr, Housecall Pro and Sears Home Services.
The sample invoice: a no-heat electric dryer
Picture a seven-year-old electric dryer that tumbles but stays cold. The technician tests the element, finds it open, and also replaces the thermal fuse. This invoice is an illustration we built from published price ranges, not a real customer’s bill.
| Line item (hypothetical) | Charged | Published fair range | Verdict |
|---|---|---|---|
| Service call and diagnosis | $95 | $50 to $150 | Fair, but ask whether it is credited |
| Heating element (OEM part) | $85 | $20 to $50 standard, $50 to $175 genuine OEM | Fair for OEM, high for generic |
| Labor, flat rate | $135 | $100 to $250 flat rate for an element | Fair |
| Thermal fuse, added | $28 | $10 to $30 as an add-on | Fair only if the vent gets checked |
| Total | $343 | $150 to $350 typical for element jobs | Within range |
HomeGuide puts a professionally replaced heating element at $150 to $350 all in, so $343 brushes the ceiling without breaking it. Each line deserves its own look, because two of them can quietly shrink.
Line one: the trip charge, and when it should disappear
Every repair starts with someone driving to your house. Angi and Fixr both list a service call fee of $50 to $80. Housecall Pro’s pricing data shows diagnostic visits at $70 to $130, and Sears Home Services says its diagnostic fee usually runs $90 to $150 for most appliances, depending on the market. Same-day or emergency diagnostics climb to $125 to $250, according to Housecall Pro, and HomeGuide adds an after-hours surcharge of $50 to $150.
The detail that changes the total is whether the fee is credited. Sears states plainly that if you go ahead with the recommended repair, the diagnostic fee is waived; you pay it only when you decline. Plenty of independent shops do the same. If our sample technician worked that way, the $343 bill drops to $248 for identical work. Ask three things on the phone before anyone shows up:
- What is the visit or diagnostic fee, and is it applied to the repair if I approve it?
- Do you charge labor by the hour or a flat rate per repair?
- Do you carry common parts for my brand on the truck, or will this need a second visit?
The third question matters more than it sounds. A second trip for a back-ordered part is where some shops add another call fee.
Line two: the part, and the markup inside it
Parts for most dryers are cheap. HomeGuide lists a standard heating element for Whirlpool, GE, Kenmore or Maytag at $20 to $50, aftermarket versions at $15 to $35, premium-brand elements for Samsung, LG or Bosch at $50 to $100 or more, and genuine OEM parts at $50 to $175. Our $85 OEM element is reasonable. The same line at $85 for a generic element would be a markup of roughly double.
For context, here is what Angi reports the common dryer parts themselves cost, before anyone installs them:
| Part | Part price | Usual symptom |
|---|---|---|
| Thermal fuse | $5 to $18 | No heat, or no start at all on many models |
| Drive belt | $14 to $32 | Motor hums, drum does not turn |
| Thermostat | $15 to $60 | No heat or overheating |
| Door switch | $8 to $30 | Will not start with the door shut |
| Drum rollers | $20 to $55 | Thumping or squealing |
| Drum bearings | $20 to $60 | Grinding or squeaking |
| Motor | $60 to $150 | Dead, buzzing or burning smell |
| Control board | $90 to $280 | Erratic cycles, blank display |
Asking for the old part back is a reasonable request and a quiet check that the part was actually replaced. You can also ask for the part number and look up its retail price yourself.
Line three: labor, by the hour or by the job
Angi and Fixr both put hourly labor for dryer work at $50 to $100, and Housecall Pro’s national average for appliance labor is about $54 an hour. Many shops skip the clock and charge a flat rate per repair instead; HomeGuide lists $100 to $250 in flat-rate labor for an element replacement.

An element swap on a standard front-load electric dryer is commonly well under an hour of hands-on work, so a $135 flat rate is paying for skill, the truck and a warranty on the work as much as for time. That is fine, as long as the price matches the job. Where flat rates bite is on small repairs: a $15 door switch billed at a $150 flat rate is mostly overhead. On the other side, HomeGuide notes that stacked or built-in units add $50 to $100 because the dryer has to come out of its slot, and high cost-of-living areas run 15% to 30% above national numbers.
Line four: the thermal fuse nobody asked for
The $28 thermal fuse is the most interesting line on the bill. A thermal fuse is a one-time safety cutoff that blows when the dryer gets too hot, and the most common reason it gets too hot is a clogged or crushed exhaust vent. Replacing it alongside a failed element is often sensible, since overheating can take out both.
The problem comes when the fuse is replaced and the vent is not checked. The new fuse will blow again, and you will pay for another visit. Angi prices vent repair at $75 to $150 and full vent replacement at $100 to $300, so ask the technician to measure airflow at the outside hood before signing off. If drying times had crept up to two cycles a load, the vent was likely part of the story.

Swap the problem, keep the template: other dryer bills
The same four lines apply to every dryer repair; only the part and the labor time move. These are Angi’s installed ranges by symptom, with Fixr’s figures for the bigger mechanical jobs.
| What the dryer is doing | Typical installed cost | Likely culprits |
|---|---|---|
| Not heating | $80 to $420 | Element, thermostat, thermal fuse; igniter on gas |
| Not spinning | $30 to $250 | Belt, drum rollers, motor |
| Will not turn on | $15 to $300 | Door switch, start switch, control board |
| Shuts off too soon | $25 to $300 | Thermostat, sensor, vent restriction |
| Overheating | $90 to $320 | Cycling thermostat, blocked vent |
| Loud noises | $10 to $450 | Rollers, idler pulley, bearings |
| Sparks or burning smell | $400 to $600 | Wiring, motor, element shorting |
| Motor replacement (Fixr) | $250 to $450 | Failed drive motor |
| Drum replacement (Fixr) | $300 to $450 | Damaged or cracked drum |
The national average dryer repair is about $180, and most households pay between $100 and $430.
Angi, 2026 dryer repair cost data
Gas dryers, premium brands and the higher end of the range
Gas models have no heating element. They light a burner with an igniter, and gas valve coils open the flow. Fixr lists gas dryer repairs at $100 to $450 against $50 to $400 for electric, with igniter replacement at $100 to $250 and ignition coils at $150 to $300; HomeGuide prices an installed igniter higher, at $200 to $400. Gas work also calls for someone comfortable with gas lines, which is not the place to improvise.
Brand shifts the bill too. Fixr’s averages put Whirlpool repairs at $200 to $350, Samsung at $150 to $350, LG anywhere from $50 to $450 and Speed Queen at $315 to $600, the last reflecting commercial-grade parts. For 2027, no change in repair pricing has been announced. The federal efficiency standards for new dryers that the Department of Energy finalized in 2024 are scheduled to apply to models made from 2028, so they should not move what a replacement costs next year.
Dryer repair questions the invoice does not answer
How much is a heating element for a dryer?
As a part, HomeGuide lists standard elements for Whirlpool, GE, Kenmore and Maytag dryers at $20 to $50 and premium-brand elements at $50 to $100 or more. A complete assembly kit runs about $70 to $110. Installed by a professional, the job usually totals $150 to $350.
Is it worth repairing a 10-year-old dryer?
Angi puts the typical dryer lifespan at about 10 to 13 years. At that age a cheap fix like a belt or thermal fuse still makes sense, but a motor, drum or control board repair that approaches half the price of a new dryer usually does not.
Does a home warranty cover dryer repair?
Many home warranty plans include dryers, but you still pay a service charge per claim, which Fixr puts at about $100. Read the plan for exclusions on vents, cosmetic parts and units considered improperly installed.
Can I replace a dryer thermal fuse myself?
Many owners do, since the part costs about $5 to $18 according to Angi. Unplug the dryer first, and on a gas model shut off the gas. The fuse blew for a reason, so clean or check the vent too, or the new one may fail quickly.
Why did the technician charge a fee and leave without fixing anything?
That fee pays for the trip and diagnosis. Many companies, including Sears Home Services, waive it when you approve the repair and keep it only when you decline. Ask about this policy when you book.
Run the 50% test on your own bill
Angi, Fixr and HomeGuide all lean on the same rule of thumb: if a repair costs more than half the price of a comparable new dryer, replacement usually wins. Fixr puts new dryers at $600 to $1,500. Apply that to our sample. Against a $600 basic dryer, a $343 bill is 57% of the replacement price and fails the test; against a $1,000 mid-range model it passes easily, and with the diagnostic fee credited it drops to $248, under half even of the cheapest dryer. So the bottom line is simple. Get the fee-credit policy in writing, ask for the part number, have the vent checked whenever a fuse or thermostat is on the bill, and divide the total by what you would actually buy next. Under 50% on a dryer younger than ten years, fix it. Over 50%, or past the decade mark with a motor or drum on the invoice, put the money toward a new one.
More appliance fixes and prices
- What a new washer and dryer cost, and where to spend
- Dryer vent cleaning prices by symptom and vent location
- Refrigerator repair costs, matched to the symptom
- Buying a new fridge and what it costs over 10 years
- Dishwasher installation cost and what to check first
- The complete home improvement cost guide
More related guides: Dishwasher repair cost, charge by charge · Appliance repair cost, symptom by symptom
Pricing method: prices were researched in November 2026 for 2027 planning and may change. Figures come from published 2026 cost data by Angi, HomeGuide, Fixr, Housecall Pro and Sears Home Services; the invoice is a hypothetical example, not a real quote. Local rates vary, so confirm with a licensed technician. See our disclaimer.
















