It is the first cold morning of the season, the thermostat reads 62, and the furnace in the basement clicks, glows, lights for a few seconds and goes quiet. Most furnace repairs that follow a morning like that cost $125 to $480, parts and labor included, with a national average near $300, according to HomeGuide. Angi’s data puts the typical job at $132 to $501, and the outliers run past $1,000.
The spread is mostly about which part failed, and the symptom usually tells you which part that is before anyone opens the cabinet. A furnace that lights and quits is a different repair, at a different price, from one that hums and never lights at all. Find your symptom below and you will know whether the quote in front of you is in range. If the answer turns out to be a new furnace, our HVAC replacement cost calculator will price that instead.
Find your symptom, then the likely bill
The installed prices below are HomeGuide’s national ranges for parts and labor on a gas furnace during a normal weekday visit. Emergency calls cost more, as the sections further down show.
| What the furnace is doing | Usual suspect | Typical installed price |
|---|---|---|
| Lights, runs a few seconds, shuts off | Dirty or failed flame sensor | $80 to $250 |
| Fan runs, no orange glow, no flame | Hot surface igniter | $100 to $250 |
| Igniter glows, burners never light | Gas valve or control board | $200 to $800 (valve), $300 to $650 (board) |
| Hums or whines, then locks out | Inducer (draft) motor | $400 to $1,100 |
| Weak airflow, grinding or squealing | Blower motor or its capacitor | $300 to $900 (motor), $100 to $250 (capacitor) |
| Runs a few minutes, stops, repeats | Limit switch or restricted airflow | $100 to $375 (switch), $100 to $400 (short-cycling repair) |
| Nothing happens, display blank | Thermostat or transformer | $190 to $480 (thermostat), $100 to $250 (transformer) |
| Soot, rolling flame or a CO alarm | Heat exchanger | $1,000 to $3,000 |
Five things to rule out before the truck rolls
Plenty of no-heat calls end with a technician flipping a switch and billing an hour for it. Spend ten minutes on these first.
- Thermostat. Confirm it is set to Heat, set above room temperature, and has fresh batteries if it takes them. A blank display points to the thermostat or its power supply, not the furnace.
- Power. Check the breaker and the light-style service switch on or near the furnace, which gets flipped off by accident more often than anyone admits.
- Filter. A clogged filter can make the furnace overheat and shut itself down. A new one costs a few dollars and takes a minute.
- Blower door. Most furnaces have a safety switch that keeps them off when the front panel is loose. Make sure it is seated firmly.
- Fault light. Many modern furnaces blink a code through a small window in the panel. Count the flashes and match them to the chart on the door; a technician who already knows the code spends less billable time finding it.
The dispatch fee and the hourly meter
Every repair starts with a visit charge. PICKHVAC puts the diagnostic fee at $75 to $150 and notes that many companies waive it when you hire them for the repair. Angi describes it as a dispatch fee or minimum charge, usually about one hour of labor. Ask on the phone whether the fee is credited toward the job. It is the easiest $100 in this article to keep.
After that, the meter runs. HomeGuide lists HVAC labor at $75 to $150 an hour, PICKHVAC at $75 to $125, and Angi at $100 to $250, a spread that tracks local wages and how busy the season is. Most of the small repairs below take an hour or less, which is why labor, not the part, makes up most of the bill.

Timing is the other lever. HomeGuide puts after-hours, weekend and holiday HVAC rates at $140 to $210 an hour, and PICKHVAC lists rush add-ons of $100 to $350. If the house can stay safely warm overnight, a weekday morning appointment saves that premium. If pipes are at risk of freezing, it does not, and the premium is cheap insurance.
Lights, runs a few seconds, then shuts off
This is the classic flame sensor failure, and it is the cheapest real repair a furnace has. The sensor is a thin metal rod that proves to the control board that the burners lit. When it is coated with residue, the board cannot confirm the flame and cuts the gas, usually within three to ten seconds, then retries a few times before locking out.
HomeGuide prices a flame sensor repair at $80 to $250, and Filterbuy’s 2026 guide lands at $75 to $250. The part itself is cheap: a White-Rodgers universal flame sensor (790-843A1) listed at $22.48 at Home Depot in November 2026. Filterbuy says cleaning the rod with fine emery cloth fixes the problem about 80% of the time, so a fair invoice for this call is often a cleaning plus the visit fee, not a new part every winter. If a company does replace the sensor, ask for the old one back.
Fan runs, but the burners never light
If the small inducer fan starts and you never see the orange glow of the hot surface igniter, the igniter has probably cracked. It is a fragile ceramic part that wears out with every heating cycle. HomeGuide puts replacement at $100 to $250 installed, and the part is not the expensive piece: Zoro listed a White-Rodgers 768A-845 nitride igniter at $42.39.
If the igniter glows and the burners still never light, the problem has moved upstream to the gas valve or the control board. HomeGuide prices a gas valve replacement at $200 to $800 and a control board at $300 to $650, with the board itself accounting for $50 to $300 of that. Boards are the part most often replaced on a guess. A careful technician checks for voltage at the valve before condemning the board, and it is fair to ask what reading led to the diagnosis.
Humming, whining or grinding before any heat
Noise usually means a motor. The inducer, or draft, motor pushes exhaust up the flue before the burners light. When its bearings go, it whines or hums, and the furnace locks out because its pressure switch never gets the airflow signal it is waiting for. HomeGuide prices inducer motor replacement at $400 to $1,100, and Angi’s range tops out near $1,500.
The larger blower motor moves warm air through the ducts. If the furnace lights but little air reaches the registers, or the cabinet grinds or squeals, the blower is the suspect. HomeGuide puts that job at $300 to $900, with the motor itself $200 to $400. Before agreeing to a new motor, ask whether the capacitor was tested. It is a $100 to $250 repair in HomeGuide’s data, and a weak one can leave a healthy motor humming without starting.
Short cycling and the furnace that overheats
A furnace that runs a few minutes, shuts down and starts again is short cycling. The usual cause is overheating, and the usual cause of overheating is restricted airflow: a filthy filter, a room full of closed registers or a blocked return grille. The high-limit switch senses the heat building up and shuts the burners off, exactly as designed.

HomeGuide prices short-cycling diagnosis and repair at $100 to $400 and a limit switch replacement at $100 to $375. Replace the switch only if it tests bad. A new switch on a furnace that is still starved of air will trip just as often, and the second visit will cost about what the first one did.
When the technician says the heat exchanger is cracked
This is the diagnosis that turns a repair call into a sales call, and the one homeowners question most. The heat exchanger keeps combustion gases separate from the air you breathe, and a crack can let carbon monoxide into the house. Many technicians will shut off the gas and tag the furnace on the spot, which is the right move if the crack is real.
It is also the most expensive repair on the list. HomeGuide prices heat exchanger replacement at $1,000 to $3,000, and PICKHVAC’s typical range runs $1,800 to $3,200, with hard jobs reaching $6,000. Set that against a whole new gas furnace at $2,000 to $5,200 in HomeGuide’s data, or $3,800 to $10,000 in Angi’s, and replacement usually wins on an older unit. Before agreeing to either, ask to see the crack on camera or in photos, check whether the exchanger is still under the manufacturer’s warranty, and get a second licensed opinion. A real crack will still be there tomorrow.
Angi’s rule of thumb: when a repair would cost more than half the price of a new furnace, replacing the furnace is usually the better buy.
Angi furnace repair cost guidance
Age belongs in that math. HomeGuide and Angi both put furnace life at 15 to 30 years, and HomeGuide leans toward replacement for units older than 20 or ones that keep breaking. Two federal changes matter for 2027. The Section 25C tax credit, which paid up to $600 toward a qualifying high-efficiency furnace, was eliminated by the 2025 One Big Beautiful Bill Act, so a replacement next year gets no federal tax help. And the Department of Energy rule requiring new gas furnaces to reach 95% AFUE still carries a compliance date of December 18, 2028, though the Supreme Court sent the legal challenge back to the D.C. Circuit in June 2026 and DOE has floated a delay to 2030. Neither changes what a repair costs in 2027; both change what a replacement buys.
Furnace repair questions that come up after the visit
Does homeowners insurance cover furnace repair?
Usually not for wear and tear, such as a failed igniter or a worn motor. Standard policies tend to cover damage from a covered event, like a fire, and exclude breakdowns caused by age. Check your policy or ask your agent; some owners add an equipment breakdown endorsement or buy a separate home warranty for this.
How much does it cost to repair an electric furnace?
HomeGuide puts electric furnace repairs at $100 to $380 and Angi at $50 to $300, generally less than gas units because there is no burner, igniter or gas valve to fail. A burned-out heating element runs $125 to $400 per coil in HomeGuide’s data.
Why do furnace repair service cost quotes vary so much between companies?
Labor rates alone range from $75 to $250 an hour across HomeGuide, PICKHVAC and Angi data. Add different dispatch fees, after-hours premiums and the choice between original-manufacturer and universal parts, and two honest quotes for the same repair can be far apart.
Will the manufacturer warranty pay for my furnace repair?
It may cover the failed part, especially on a registered furnace that is still within its parts warranty term, but labor is usually billed separately. Give the technician the model and serial number before a part is ordered so warranty coverage can be checked.
Is it safe to keep using a furnace that keeps shutting off?
A furnace that shuts itself off is usually a safety control doing its job, but repeated cycling wears parts and can hide a bigger problem. If you smell gas, see soot around the cabinet or hear a carbon monoxide alarm, turn the furnace off, leave the house and call for help before anything else.
Who to call, depending on what you notice
- You smell gas: leave without flipping switches, then call your gas utility’s emergency line or 911 from outside. The repair company comes after.
- The carbon monoxide alarm sounds: get everyone out and call 911. Do not restart the furnace until it has been inspected.
- The furnace is only a few years old: call the company that installed it first. The part may be under warranty, leaving only labor to pay.
- A technician condemned the heat exchanger: call a second licensed HVAC company for an independent look before paying for a new furnace.
- Everything else: a local HVAC contractor, with three questions ready: the diagnostic fee, whether it is credited toward the repair, and the hourly rate if the visit runs long.
Other heating bills we have taken apart
- Furnace replacement cost, 80% vs 96% models
- What a yearly furnace tune-up costs
- HVAC inspection prices
- Heat pump cost compared with a new furnace and AC
- A new HVAC system for a 2,000-square-foot home
- Air duct cleaning prices
- The complete home improvement cost guide
- HVAC replacement cost calculator
More related guides: HVAC repair cost vs a new system
Pricing method: prices were researched in November 2026 for 2027 planning and may change. Repair ranges come from HomeGuide, Angi, PICKHVAC and Filterbuy; part prices are retailer listings from Home Depot and Zoro; regulatory dates come from Contracting Business and ACHR News reporting. Local prices vary, so confirm quotes and any safety concern with a licensed HVAC contractor. See our disclaimer.
















