The most common mistake in pricing a new HVAC system is starting with the square footage. Two houses of 2,000 square feet can draw quotes thousands of dollars apart, and the size of the house explains very little of the gap. For a typical 2,000-square-foot home, This Old House puts a new central AC and gas furnace at about $8,283 on average, with a range of $5,634 to $14,686. CBS News, citing contractor data, gives a wider band of $7,000 to $20,000 for a basic furnace and AC replacement in a home that size.
Climate, fuel and the condition of the ducts move the number far more than the floor plan does. So rather than one average, we priced four example homes, all 2,000 square feet, start to finish. They are illustrations built from published estimates, not quotes. To plug in your own numbers, try our HVAC replacement cost calculator.
Four houses, one floor area, four totals
| Example home | System | Published range for 2,000 sq ft | Our example total |
|---|---|---|---|
| Midwest ranch | Gas furnace + central AC, ducts reused | $5,634 to $14,686 | About $8,600 to $8,900 |
| All-electric Georgia house | Heat pump + air handler | $5,558 to $14,483 | About $8,500 to $8,800 |
| Northeast colonial | Dual fuel: heat pump + gas furnace | $7,252 to $19,051 | About $11,100 to $11,400 |
| 1978 split-level, failing ducts | 16.1 SEER2 AC + gas furnace + new ducts | $7,800 to $14,686 before ducts | About $12,400 to $14,200 |
One caution on method. This Old House built its figures from three online distributors’ unit prices plus a markup, with labor estimated from install hours. A local dealer with its own overhead, warranty terms and brand can land well above those averages, which is why CBS’s ceiling sits near $20,000.
Home one: a Midwest ranch replacing a tired furnace and AC as a pair
This is the baseline job. A 20-year-old gas furnace and the AC paired with it are both near the end, the ductwork is sound, and the owners want the same kind of system back at a mid-range efficiency. This Old House sizes a 2,000-square-foot home at 3.5 tons and prices a 14.3 SEER2 AC with a gas furnace at $8,283 on average.
- Equipment: $4,935 to $8,933 for the furnace, condenser and coil at 14.3 SEER2
- Labor: $1,213 to $2,763, depending on region
- Permit: $250 to $400
- Thermostat: $39 to $217
- Example total: roughly $8,600 to $8,900 with the average system price, permit and a basic to mid-range thermostat
Replacing both pieces at once is usually the right call here. The indoor coil sits on top of the furnace and has to match the new condenser, so swapping only the AC often means paying for a new coil anyway, and a second crew visit later. If the furnace is under ten years old and healthy, an AC-only replacement is the exception worth pricing; This Old House puts that job at $7,582 on average for this size of home.
Home two: an all-electric Georgia house that goes heat pump
In much of the South, the old system is already a heat pump or an AC with electric strips, and gas may not be on the street. A heat pump with an indoor air handler averages $8,166 for 2,000 square feet in the This Old House figures, with a range of $5,558 to $14,483. Add a permit and thermostat and our example lands around $8,500 to $8,800.
Two regional facts help this owner. Labor in the South runs at the bottom of the national range, as low as $1,213 for the install in the This Old House data, against up to $2,763 in the Northeast and Hawaii. And the efficiency floor matters: the Southeast and Southwest carry a 14.3 SEER2 minimum for new central air, so the cheapest 12.4 SEER2 units in the price tables are not an option. Budget from the 14.3 row.
The one line to watch is electrical. If the panel is full or the house still has older service, a heat pump job can turn into a panel job; our electrical panel replacement guide prices that separately. Carrier, for its part, quotes heat pumps at $6,000 to $25,000 installed in 2026 across all sizes and tiers.
Home three: a Northeast colonial paying the dual-fuel premium
Cold-climate owners with gas often split the difference: a heat pump handles cooling and mild-weather heat, and a gas furnace takes over on the coldest days. That pairing costs the most of the four. This Old House puts dual fuel at $10,787 on average for 2,000 square feet, and the range runs to $19,051 at the top.
Our example colonial lands around $11,100 to $11,400 with permit and thermostat, and that probably understates it, because this house sits where installers charge the most. The gap between the South’s lowest labor figure and the Northeast’s highest is about $1,550 on the same 3.5-ton job, before any difference in equipment. Two-story layouts with an attic air handler can add more.
Is the premium worth it over a plain furnace and AC, about $2,500 less on average? It depends on your gas and electric rates more than on the equipment. Our heat pump cost comparison runs that math. If the answer is close, the cheaper pair is the safer bet.
Home four: a 1978 split-level where the ducts are the problem
Some houses need more than new boxes. The owners of this split-level want a quieter, more efficient system, a 16.1 SEER2 AC with a gas furnace, and the installer finds crushed, leaking flex duct in the attic. The equipment alone averages $10,573 at that efficiency in the This Old House tables, with a range of $7,800 to $14,686.
- Higher-efficiency AC and furnace: $10,573 average
- Ductwork replacement: $1,500 to $3,000 (This Old House); CBS cites contractor data that bad or missing ducts can add about $3,000
- Permit and thermostat: $289 to $617 combined
- Example total: about $12,400 to $14,200
This is the house where a premium system can be wasted money. A high-SEER2 unit pushing air through leaky ducts will not deliver its rated efficiency, so if the budget forces a choice, fix the ducts and drop to the 14.3 SEER2 tier. The difference between those two tiers averages about $2,300 in the tables, close to what the duct work costs.
Tonnage is where a 2,000-square-foot quote goes wrong
Every example above assumes 3.5 tons, the size This Old House treats as typical for 2,000 square feet. Your house may need less. Insulation, window area, ceiling height, shade and air sealing all change the load, and a well-sealed newer home can need a ton less than a drafty one of the same size. An oversized system costs more to buy, short-cycles, and leaves rooms clammy because it shuts off before it pulls out the humidity.
The fix is a Manual J load calculation, the method published by the Air Conditioning Contractors of America. Ask each bidder whether they ran one for your house or simply matched the old unit’s size. A contractor who replaces a 4-ton unit with another 4-ton unit without measuring anything is guessing, and you are paying for the guess. If you recently added attic insulation or new windows, the old size is even more likely to be wrong.
Manufacturers are raising prices on the boxes for 2027
All four examples rest on mid-2026 equipment prices, and those are moving up. On its third-quarter earnings call, reported by ACHR News on November 2, Carrier said it is raising residential equipment prices 8%, effective toward the end of this quarter. Trane put through two residential increases of up to 5% each in 2026, on April 1 and July 1. Carrier says about half of its roughly $800 million in input-cost headwinds this year came from tariffs, with copper, steel and aluminum also cited.
“It’s really a zip code by zip code space.”
Trane’s CFO on residential HVAC pricing, as reported by ACHR News, September 2026
What does 8% mean for a homeowner? Applied to home one’s equipment range of $4,935 to $8,933, it is about $395 to $715, if a dealer passes the whole increase through. That is our arithmetic, not a forecast; Carrier also said it realized less pricing in 2026 than it planned, a sign that soft demand (Carrier now expects a residential market of 7.5 million to 8 million units this year, down from about 9.2 million in 2024) is limiting how much sticks. No manufacturer had published a 2027 list price schedule for homeowners when we checked in November 2026.
Questions owners ask between the second and third quote
Is there still a federal tax credit for a new HVAC system in 2027?
No. The IRS says the Energy Efficient Home Improvement Credit (Section 25C) applied to qualifying property placed in service from 2023 through 2025. It had allowed up to $2,000 a year for qualifying heat pumps and up to $600 per item for qualifying central AC units and furnaces. Systems installed in 2026 or 2027 do not qualify, though some utilities and states run their own rebates, so check with your utility before you buy.
Is an electric furnace cheaper than gas for a 2,000 sq ft home?
To install, slightly. This Old House puts a central AC with an electric furnace at $7,343 on average for 2,000 square feet, against $8,283 with a gas furnace. Electric resistance heat usually costs more to run in cold climates, so the savings at install can disappear within a few winters. Compare your local electric and gas rates first.
How long will a new HVAC system last?
Carrier says a heat pump typically lasts 10 to 15 years. Gas furnaces often last longer than the outdoor unit they are paired with, which is one reason contractors push to replace both at once. Annual maintenance and clean filters help either one reach the upper end of its range.
What does furnace and AC replacement cost if I pick the cheapest efficiency?
For a 2,000 sq ft home, This Old House lists a 12.4 SEER2 system at $5,634 to $10,765, averaging $7,570. Whether you can install it depends on your region’s federal minimum: the Southeast and Southwest require at least 14.3 SEER2, which averages $8,283 with a gas furnace.
Six lines every 2,000-square-foot quote should show
Get at least three bids, and do not compare totals until each one shows these lines. A bid that cannot fill them in is not cheaper; it is vaguer.
- The tonnage and how it was chosen, ideally from a Manual J calculation for your house
- Exact model numbers for the outdoor unit, the furnace or air handler and the coil, plus the SEER2 rating of the matched set
- Ductwork scope: reused as is, sealed, partly replaced or fully replaced, with a separate price
- Permit and inspection, listed rather than assumed
- Electrical work, including any breaker, disconnect or panel changes a heat pump needs
- Labor and equipment warranty terms in years, and whether the manufacturer warranty requires registration
Pricing the system one piece at a time
- Home improvement costs in 2027: the complete price guide
- HVAC replacement cost calculator
- Furnace replacement cost by efficiency and climate
- Central air conditioner cost, decoded line by line
- Heat pump cost compared with a new furnace and AC
- Mini split cost for one room or the whole house
- HVAC inspection cost and what each tier checks
More related guides: HVAC repair cost vs a new system · Geothermal heating cost over 20 years
Pricing method: prices were researched in November 2026 for 2027 planning and may change. System and add-on ranges come from This Old House (updated June 2026), CBS News (May 2026) and Carrier (September 2026); manufacturer price increases from ACHR News (September and November 2026); tax credit status from the IRS. Example homes are hypothetical, and their totals are our arithmetic, not quotes. Get written bids from licensed local contractors. See our disclaimer.
















